schaut gut aus! schön hoch! würde gerne noch paar Bilder mehr sehen von der Aufnahme und auch das von Hinten. Gruß CAT
Erfahrung ConStands Zentralständer
-
jns_prz -
16. August 2021 um 11:10 -
Unerledigt
-
-
Moin.
Ich hab mir nun auch einen zugelegt… 😉
Kann mir jemand sagen, mit wie viel nm die Hülsen an der DD fest gezogen werden müssen?
Danke! ✌🏻
-
Kann morgen nachschauen, weiß es nicht mehr auswendig.
-
Bei der Capo und der DD1200 sind die Schrauben, bzw. Die Muddi, mit 80Nm angegeben.
Dürfte bei deiner gleich sein, sind ja die gleichen Rahmen
-
Kann morgen nachschauen, weiß es nicht mehr auswendig.
Das wäre klasse. Danke.
-
Habe im WHB geschaut. Heißt „Befestigungsschraube Seitenteile am Motor“. Müsste die M12x282 sein. Und Phil hat recht. Anzugsdrehmoment 80Nm.
-
Danke euch! 👍🏻
-
schaut gut aus! schön hoch! würde gerne noch paar Bilder mehr sehen von der Aufnahme und auch das von Hinten. Gruß CAT
Mhh, gibbet den irgendwann Bilder von Hinten?
-
So ausreichend!?
-
Die Montage an sich ist wirklich sehr simpel.
Fast verzweifelt bin ich dann aber bei der justierung der Halteplatte am Ständer...
Ich habe diese einfach nicht so ausgerichtet bekommen, dass ich die Halteplatte am Ständer montiert ohne Probleme in die Aufnahmebuchsen an der DD schieben konnte; irgendwas verkantete immer.
Perfekt ist es jetzt noch immer nicht aber die DD "hängt" erst mal und im Frühjahr mit etwas mehr Muße, lässt sich das sicherlich auch noch so butterweich justieren, wie in den Youtube-Videos...
-
War bei mir genauso. Mit justieren is da nicht viel, ich war schon am Anschlag. Ging am Anfang kaum rein und noch schlechter wieder raus. Nach ein paarmal mit Gewürge rein und raus und etwas Schmierung in der Hülse wurde es immer besser und mittlerweile flutscht es ganz easy.
-
Dann hab ich mich also nicht zu blöd angestellt...
Geschmiert habe ich auch und nur die Halteplatte allein flutscht ja super aber wenn alles montiert ist, hakt es gewaltig. In dem Zustand wäre es mir für den täglich Gebrauch zu umständlich; für den Winterschlaf aber ok.
-
Danke für das Foto.
Somit ist meine Aussage, dass sich der Hauptrahmen verwindet, wie bei meiner DD900 damals, widerlegt.
Das Kennzeichen ist genau mittig zum HR.
Deine Bella schwebt mit beiden Rädern in der Luft, auch wenn man es nicht wirklich erkennen kann.
Mit dem Einführen der Aufnahme hatte ich komischerweise keinerlei Probleme.
An und für sich ist der Zentralständer ja eine wirklich feine Sache.
-
- Offizieller Beitrag
Wenn ich das hier vom ConStands lese, bin ich froh doch den Framic zu haben. Zudem ist die Adapterbuchse "unsichtbar" verbaut, was mir persönlich sehr gefällt.
aprilia-shiver.de/attachment/10422/
Fotos waren ja schon im Beitrag: >RE: Montageständer vorne + hinten Shiver 900
und in
-
Vielen dank für die Bilder !!
-
Kurze zwischenmeldung nach ein paar Monaten in der Luft..
Rahmen weder verzogen noch andere Probleme gehabt.
Die kleine hängt seit November in der Luft & das bis auf 2x Anlassen damit nichts fest wird, dauerhaft. -